Ireland/Eire/Isle of Man/Scilly Isles by arrangement other destinations phone for details Typical delivery times of 1-2 working days. Orders will be despatched as follows: To business addresses only £9.95 (Exc VAT) delivery charge (subject to change depending on account level) Free delivery with net order values of £100 and over (Exc VAT) to the UK Mainland Orders to N. You will be notified by the chosen dealer once your order is ready to collect, estimated time is 2-3 days (depending on national holidays and dealer opening hours). The detours mounts to the sides of the rails, while mine mounts to the sides and the front of the rails via the tow hook brackets.Select a collection point from our network of available dealers. The leverage is the same and the mounting points on the frame are basically the same. But thats more about minor flexing than catastrophic failure. I think the winch plate I'm using makes up for the deleted middle section because its got a couple inch tall vertical sections on both front and back which makes it alot stiffer than the detours one. I deleted that middle area and so the winch plate itself becomes the only thing joining the two angle brackets (besides the unibody). The detours mount works the same way, only they used a continuous section of steel between the two mounts. I see what you are saying about leverage but I dont think its as dramatic as you are making it sound. If you think this is a recipe for disaster I'd like to know why.Ĭlick to expand.Its not mounted to sheet metal unless you are saying the frame rail mounts (which every winch bumper mounts to) are sheet metal and unsuitable for winch mounting. Thoughts? I'm looking for criticism! I have never used a winch or done any recovery with the Jeep. The picture with the bumper off only shows the passenger bracket installed. The hardware I have on there is just temporary until I go buy the good stuff. Im not worried so much cosmetically as much as functionally. Something I may have overlooked is having enough clearance BEHIND the winch.right now any cable loops on the back of the winch will hit the grill. I think the stock approach angle was pretty much maintained here. But whatever I wanted less weight and I think these are plenty strong. Now, I could have just done this with one long "bracket" instead of making two little ones, and it would have been much stronger and stiffer. Also in the new brackets to allow the bolts that mounted the brackets you welded onto to mount to the Jeep. Holes need to be drilled in the new brackets and the winch mount so it all bolts together. You can slide the bumper bracketry around to make room. Your new brackets then pop up over the stock bumper. You are just making two "L" shaped brackets and welding them to the stock XJ tow hook brackets that go on the FRONT of the cross member (see pics). Or get the scrap yard to cut the pieces for you. I got a set of 5 (or 6?) that included T50 and T55 for 10 at autozone.īandsaw to cut the angle iron or possibly a hacksaw or sawzall if you are really slumming it. The usual sockets/wrenches/ratchets, etc.plus some torx bits for the bumper. Welder to weld the 3/8" angle iron to the stock XJ tow hook bracket. Transfer punches, auto center punch, and pointy center drill are what I used to get all the holes marked out in the right spots. Critical parts are putting the holes in the right places, doing high quality welds, making sure all the mating surfaces are flat and burr free, and making sure everything lines up right.ĭrill press is nice because you will have to drill some around 1/2" dia holes in steel, I suppose a high quality hand drill could work. But you are just making two 3/8" L brackets and welding them to the stock jeep tow brackets, then adding holes as needed for all the bolts. Im not putting every little detail in here. You need about qty 8 of at least M12 x around 40mm long I think with nuts and washers. Various quality (10.9 grade or equivalent) hardware.probably 5 if you get it at the junkyard. I got a set at my local pick and pull for around 25. To do it exactly the way I did it, you make two 5" long brackets.so thats 10" total. I got 48" worth for 10 at my local scrap yard. 5" leg, 3/8" thick, about 10" long piece of steel angle iron "L" shape. You could just make this out of steel plate or U-channel though, so lets say it costs 10 in material. I used a harbor freight winch mount plate which goes for about 50.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |